Skip to content

Paver Installation · Redmond

Paver Installation in Redmond

A large share of Redmond sits inside a homeowners association, and on the Ridge and the newer plats that changes the order in which a paving project happens. The material, the colour and sometimes the pattern have to clear an architectural committee before anything is ordered, and a committee works to its own calendar rather than to your build window. The practical consequence is that the specification stops being purely a taste decision and becomes a submission — which is manageable when it is planned for and expensive when it is discovered after a pallet has arrived. The second Redmond-specific issue is matching: on a plat where the original hardscape was laid across many houses at once, a new area that does not tie back to it announces itself from the street.

Typical range
$18–$40 per square foot installed
From our base
30–45 minutes from Capitol Hill via SR-520
Ground here
Glacial till on the upland at Education Hill, Union Hill and Novelty Hill, with alluvial valley-floor soils and a high water table along the Sammamish River corridor.

Artificial turf lawn held level by split-face block retaining walls with a paver walk alongside in Redmond

What we get called about

Paver Installation problems specific to Redmond.

Redmond splits into two landscapes with different problems. On the valley floor near the Sammamish River the ground is flat and the water table is high, so drainage design is constrained by how much fall is available and where a system can legitimately discharge. Up on Education Hill, Union Hill and Novelty Hill the lots are large, the access is excellent and the work is design-led rather than remedial. The other Redmond factor is HOA density in the newer developments, where architectural review is a real scheduling item.

  • A paving choice rejected by an architectural committee after ordering
  • New work that does not tie back to the plat’s original hardscape
  • A build window lost to an approval cycle nobody scheduled for
  • Original developer paving that is discontinued and cannot be matched
  • Front-of-house work governed by rules the back garden is exempt from

Worth knowing in Redmond

Get the submission in before you get quotes, not after. Committees generally want material, colour and a sketch of the area, all of which you can produce from samples without committing to anybody. It costs nothing and it stops a build window being lost to an approval that was always going to be needed.

Working with an architectural committee

Associations vary enormously in how they operate, and the only reliable approach is to read the specific covenants rather than assume. Some govern only what is visible from the street, some govern the whole lot, and a few have a pre-approved materials list that makes the whole question straightforward.

What committees almost always want is the same short set of things: what the material is, what colour it is, roughly where it goes and how big it is. Physical samples carry more weight than photographs, and a simple dimensioned sketch carries more than a description. None of that requires a contractor to be appointed, which is why it is worth doing first.

The commonest failure is timing rather than refusal. A committee that meets monthly can add weeks to a project that was quoted as starting immediately, and in a climate with a compressed build window those weeks can be the difference between paving in July and paving in October. We ask about association requirements at the first visit for exactly this reason.

The method

How we build paver installation, wherever the job is.

The sequence does not change between neighbourhoods — what changes is the ground it is applied to. Full detail on the paver installation service page.

  1. 01

    Read the ground before pricing the surface

    What the subgrade is, how wet it gets, and where water currently goes. On a till lot those three answers change the build more than the choice of paver does.

  2. 02

    Set levels and falls first

    Every surface gets a fall, including the ones that look flat. Where water leaves is decided before a shovel moves, not adjusted at the end once the levels no longer allow it.

  3. 03

    Excavate and compact the subgrade

    Down to competent ground, then compacted before any rock goes in. A good base built on an uncompacted subgrade just moves the failure one layer down.

  4. 04

    Build the base in lifts

    Layer by layer to the specified depth, with a plate or roller sized for the job rather than whatever is on the van. This stage decides whether the surface is still flat in ten years.

  5. 05

    Screed, lay, cut and restrain

    Bedding course screeded to depth, units laid off a string line, perimeter saw-cut, and edge restraint fixed before any joint is filled.

  6. 06

    Joint, compact and wash down

    Polymeric sand swept in, the field compacted to seat the units, then the whole area washed off — the last step is the one a rushed crew skips.

What it costs in Redmond

$18–$40 per square foot installed

Redmond paver installation runs $18 to $40 per square foot. The specification rarely moves the number much here; the schedule does. Work that has to wait on a committee cycle can be pushed out of a season, and a summer job that becomes an autumn one is a wetter, slower build. Where an existing paving type is discontinued, sourcing a close match — or deliberately choosing a contrasting one that reads as intentional — is a design decision worth making early rather than at the supplier.

  • No down payment

    You pay after the project is fully completed.

  • Fixed price, agreed up front

    The estimate you sign is the price you pay.

  • 0% interest for up to 6 months

    Spread the cost with no interest.

  • Warranty on hardscaping

    Covers hardscape work; vegetation excluded.

Local questions

Paver Installation in Redmond, answered.

General questions about this service are on the service page. These are the ones that only come up here.

Does my HOA have to approve a patio?

Frequently yes, and the answer is in your covenants rather than in any general rule. Some Redmond associations govern only what is visible from the street and take no interest in a rear garden; others require submission for any hard surface anywhere on the lot, including material and colour. A few maintain an approved materials list, which makes the process quick. What we would strongly advise against is assuming the back garden is exempt because a neighbour did something similar — approvals are granted case by case and an unapproved installation can, in the worst instance, have to come out.

Can you match the original paving on my plat?

Usually closely, occasionally exactly, and it depends on how long ago the development was built. Manufacturers change ranges, and a unit laid fifteen years ago may simply not be made any more — in which case matching means finding the nearest current equivalent in size and colour family, which is a sample exercise rather than a catalogue one. Weathering also works in your favour over time: a close match that looks slightly fresh on the day it goes down blends within a couple of seasons. Where nothing sensible matches, the better move is a deliberate contrast at a clean boundary rather than a near-miss.

How long does approval usually take?

It depends entirely on how often the committee meets, which is the single most useful thing to find out early. Some review submissions continuously and turn them round in days; others meet monthly, which means a submission sent just after a meeting waits the better part of five weeks before it is even looked at. Add a round of questions and a resubmission and a straightforward project can lose a month and a half. That is why we raise it at the first visit rather than at contract stage — it changes when work can start far more often than it changes what gets built.

Is the front of my house treated differently from the back?

Very often, and it is the most common misunderstanding we run into. A great many covenants concern themselves with the streetscape — what the plat looks like as a whole — and are correspondingly detailed about driveways, front walks and anything visible over a fence, while saying little about a rear garden nobody can see. That means a front walkway may need submission where an identical patio behind the house does not. Because the distinction is written into each association’s own documents rather than being standard, the only reliable answer comes from reading yours.

Serving Redmond and surrounding neighbourhoods

30–45 minutes from Capitol Hill via SR-520.

Downtown Redmond · Education Hill · Grass Lawn · Overlake · Idylwood · Bear Creek · Union Hill · Novelty Hill · Sammamish Valley

98052 · 98053

Everything we do in Redmond →

Recent work

Built in Redmond.

Built-in outdoor kitchen island and fire pit on a paver patio with a low seat wall

Get a paver installation estimate in Redmond.

We come out, look at the ground, and put a fixed written price together. No deposit, and it does not change once agreed.

Free estimate

Paver Installation in Redmond — get a price.

Three minutes on the form. We reply during office hours, Monday – Friday, 9:00 AM – 7:00 PM, and we come out and look at the site before quoting anything.

Or call (425) 533-9734

Takes under a minute. No deposit is required to book work — you pay when the project is finished. Prefer to talk? Call (425) 533-9734

Call NowFree Estimate